Wingits Grab Bar GBW40 Manuel d'utilisateur télécharger pdf

WINGITS

GBW40, GBW50, SRGBW40

World’s Strongest Fastener

™

Specifications

• GBW40 Standard WINGITS

is used in walls framed with

2 x 4’s (3-1/2” hollow or larger). Comes with stainless steel 4”

screw for walls up to 1 1/4” thick.

• SRGBW40 Reverse WINGITS

is used in walls framed with

2 x 3’s (2-1/2” hollow or larger).

• GBW50

Comes with stainless steel 5” screw for thicker walls.

NEVER INSTALL ANY FASTENER INTO WET OR DETERIORATING WALLS

Structural Blocking Must Be Used In PLAIN 1/2” DRYWALL When

Attempting To Meet Commercial Building Codes.

Commercial Grab Bar Fastening System Installation Guide

WINGITS

Grab Bar Fastening Systems Exceeed Building Codes

For Grab Bars In The Following Wall Substrates:

• 5/8” Drywall - Painted or Wallpapered

• 1/2” or 5/8” Drywall with Tub Surrounds

• 1/2” or 5/8” Drywall with Tile, Marble or Stone

• 1/2” or 5/8” Drywall with any Panel Types including Fiberglass,

Faux Marble, Acrylic and Plastics

• Multiple Layers of Drywall, Plaster and Lathe

• 1/4” Acrylic/Fiberglass Tub Surrounds

• Most Wall Panels, All Masonry Type Boards

Before You Install:

ADAAG recommends Grab Bars be installed horizontally 33” - 36”

from the floor.

• Verify the length of the grab bar by measuring from the inside of

one flange to the outside of the other.

• To ensure adequate clearance, a stud finder should be used to

verify there are no studs within the area where the WingIts

will

be installed. Make sure that there is at least 1.5” away from

the edge of the stud. If concerned, drill a pilot hole and insert

a piece of wire in the shape of an “L” - twirl the wire to make

sure there is nothing in the way. Once inserted, each wing

assembly will spring open almost 3” in diameter

• Tools Required: Screwdriver, 1.25” Drill

(our APACHE200 rated at 200 holes in ceramic wall tile)

WINGITS

GBW40, GBW50, SRGBW40

World’s Strongest Fastener

™

GBW40

Specifications

• GBW40 Standard WINGITS

is used in walls framed with

2 x 4’s (3-1/2” hollow or larger).

• SRGBW40 Reverse WINGITS

is used in walls framed with

2 x 3’s (2-1/2” hollow or larger).

• WINGITS

come standard with a stainless steel 4” screw for walls

up to 1 1/4” thick. Larger screws available for thicker walls.

NEVER INSTALL ANY FASTENER INTO WET OR DETERIORATING WALLS

Structural Blocking Must Be Used In PLAIN 1/2” DRYWALL When

Attempting To Meet Commercial Building Codes.

Commercial Grab Bar Fastening System Installation Guide

WINGITS

Grab Bar Fastening Systems Exceeed Building Codes

For Grab Bars In The Following Wall Substrates:

• 5/8” Drywall - Painted or Wallpapered

• 1/2” or 5/8” Drywall with Tub Surrounds

• 1/2” or 5/8” Drywall with Tile, Marble or Stone

• 1/2” or 5/8” Drywall with any Panel Types including Fiberglass,

Faux Marble, Acrylic and Plastics

• Multiple Layers of Drywall, Plaster and Lathe

• 1/4” Acrylic/Fiberglass Tub Surrounds

• Most Wall Panels, All Masonry Type Boards

Before You Install:

ADAAG recommends Grab Bars be installed horizontally 33” - 36”

from the floor.

• Verify the length of the grab bar by measuring from the inside of

one flange to the outside of the other.

• To ensure adequate clearance, a stud finder should be used to

verify there are no studs within the area where the WingIts

will

be installed. Make sure that there is at least 1.5” away from

the edge of the stud. If concerned, drill a pilot hole and insert

a piece of wire in the shape of an “L” - twirl the wire to make

sure there is nothing in the way. Once inserted, each wing

assembly will spring open almost 3” in diameter

• Tools Required: Screwdriver, 1.25” Drill

(our APACHE200 rated at 200 holes in ceramic wall tile)

WINGITS

GBW40, GBW50, SRGBW40

World’s Strongest Fastener

™

GBW40

Specifications

• GBW40 Standard WINGITS

is used in walls framed with

2 x 4’s (3-1/2” hollow or larger).

• SRGBW40 Reverse WINGITS

is used in walls framed with

2 x 3’s (2-1/2” hollow or larger).

• WINGITS

come standard with a stainless steel 4” screw for walls

up to 1 1/4” thick. Larger screws available for thicker walls.

NEVER INSTALL ANY FASTENER INTO WET OR DETERIORATING WALLS

Structural Blocking Must Be Used In PLAIN 1/2” DRYWALL When

Attempting To Meet Commercial Building Codes.

Commercial Grab Bar Fastening System Installation Guide

WINGITS

Grab Bar Fastening Systems Exceeed Building Codes

For Grab Bars In The Following Wall Substrates:

• 5/8” Drywall - Painted or Wallpapered

• 1/2” or 5/8” Drywall with Tub Surrounds

• 1/2” or 5/8” Drywall with Tile, Marble or Stone

• 1/2” or 5/8” Drywall with any Panel Types including Fiberglass,

Faux Marble, Acrylic and Plastics

• Multiple Layers of Drywall, Plaster and Lathe

• 1/4” Acrylic/Fiberglass Tub Surrounds

• Most Wall Panels, All Masonry Type Boards

Before You Install:

ADAAG recommends Grab Bars be installed horizontally 33” - 36”

from the floor.

• Verify the length of the grab bar by measuring from the inside of

one flange to the outside of the other.

• To ensure adequate clearance, a stud finder should be used to

verify there are no studs within the area where the WingIts

will

be installed. Make sure that there is at least 1.5” away from

the edge of the stud. If concerned, drill a pilot hole and insert

a piece of wire in the shape of an “L” - twirl the wire to make

sure there is nothing in the way. Once inserted, each wing

assembly will spring open almost 3” in diameter

• Tools Required: Screwdriver, 1.25” Drill

(our APACHE200 rated at 200 holes in ceramic wall tile)

1 2

Résumé du contenu

Page 1 - World’s Strongest Fastener

WINGITS®GBW40, GBW50, SRGBW40World’s Strongest Fastener™Specifications• GBW40 Standard WINGITS® is used in walls framed with 2 x 4’s (3-1/2” hollow

Page 2 - www.wingits.com

Toll Free: 877-894-6448 www.wingits.com • [email protected] Solutions Company™View Installation Videos at: www.wingits.comInstalli

Modèles reliés Grab Bar GBW50

Commentaires sur ces manuels

Pas de commentaire

Wingits Grab Bar GBW40 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la maison Wingits Grab Bar GBW40. WINGITS Grab Bar GBW40 User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés Grab Bar GBW50

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la maison Wingits Grab Bar GBW40